SKALE-1850 updated README.md

README.md

@@ -2,15 +2,16 @@
 
 ## Intro
 
-sgxwallet is a next generation hardware secure crypto wallet that  is based on Intel SGX technology. It currently supports Ethereum and SKALE, and will support Bitcoin in the future.
+**sgxwallet** is a next generation hardware secure crypto wallet that  is based on **Intel SGX** technology. It currently supports **Ethereum** and **SKALE**, and will support **Bitcoin** in the future.
 
-sgxwallet has been tested on Ubuntu Linux 18.04.
+**sgxwallet** has been tested on **Ubuntu Linux 18.04**.
 
 ## Install Prerequisites
 
-```sh
-sudo apt-get install build-essential make cmake gcc python libssl-dev libboost-all-dev libgmp3-dev libprotobuf10 libprocps-dev flex bison automake libtool texinfo libjsonrpccpp-dev
 ```
+sudo apt-get install build-essential make cmake gcc g++ python libprotobuf10 flex bison automake libtool texinfo
+```
+libssl-dev libboost-all-dev libgmp3-dev libprocps-dev libjsonrpccpp-dev
 
 ## Clone this repository and its submodules
 
@@ -18,12 +19,12 @@ sudo apt-get install build-essential make cmake gcc python libssl-dev libboost-a
 
 ## Enable SGX on your machine
 
-To build and run sgxd, you'll need Intel SGX capable hardware. Most Intel chips that were produced after 2015 support SGX.
+To build and run **sgxd**, you'll need **Intel SGX** capable hardware. Most Intel chips that were produced after 2015 support **SGX**.
 
--   Enter BIOS of you machine by pressing and holding Del or F2 on bootup and verify that BIOS includes SGX options.
-    If not, your machine cant run SGX.
+-   Enter **BIOS** of you machine by pressing and holding **Del** or **F2** on boot-up and verify that **BIOS** includes **SGX options**.
+    If not, your machine cant run **SGX**.
 -   Set SGX in BIOS as `enabled` or `software-controlled`.
--   If you can set SGX to `enabled` you are done! Proceed with "Install SGX Driver" section 
+-   If you can set SGX to `enabled` you are done! Proceed with "Install SGX Driver" section
 -   If not, set SGX in BIOS to `software-controlled` and then enable by running a sgx-enable utility, as described below.
 
 ## Enable "software-controlled" SGX
@@ -31,7 +32,7 @@ To build and run sgxd, you'll need Intel SGX capable hardware. Most Intel chips
 To enable SGX using a software utility:
 
 -   Build `sgx-enable` utility by typing `cd   sgx-software-enable; make`
--   Run `./sgx-enable`.  Verify that it says that SGX is successfully enabled
+-   Run `./sgx-enable`.  Verify that it says that **SGX** is successfully enabled
 
 ## Install SGX driver
 
@@ -50,7 +51,7 @@ If you do not see the `isgx` device, you need to troubleshoot your driver instal
 
 ## Install automake 1.15
 
-Currently the build builds with automake 1.15. You need to install it since Ubuntu 18 comes with automake 1.16 by default.
+Currently the build builds with **automake 1.15**. You need to install it since Ubuntu 18 comes with **automake 1.16** by default.
 
 `cd scripts; sudo dpkg -i automake_1.15.1-3ubuntu2_all.deb`
 
@@ -58,15 +59,15 @@ Currently the build builds with automake 1.15. You need to install it since Ubun
 
 Dependencies only need to be built once.
 
-```sh
+```
 cd scripts; ./build.py
 ```
 
 ## Configure
 
-Cd to the project top dir, then run
+Co to the project's top directory, then run
 
-```sh
+```
 autoconf
 automake
 ./configure
@@ -74,21 +75,25 @@ automake
 
 ## Build
 
-Cd to project top dir and run
+Go to project's top directory and run
 
-```sg
+```
 make
 ```
 
 ## Running sgxwallet
 
-Type `./sgxwallet`
+Type:
+
+```
+`./sgxwallet`
+```
 
 ## Development
 
 Note that `configure, Makefile` and `Makefile.in` files are created by `automake` tools on the fly.  
 Please do not add these files to the source tree!
 
-To add new source and include files to app and enclave, edit the corresponding "Makefile.am" file and then re-run configure. 
+To add new source and include files to app and enclave, edit the corresponding **Makefile.am** file and then re-run configure.
 
-If you change .edl file, you need to re-run configure too.
+If you change **.edl** file, you need to re-run configure too.